4/10/2024 0 Comments Ti connect 1.6.1 exeGUI Edit tab: The length field is not validated properly.The workaround is to perform a mass erase before connecting to the device (SRFPROG-241). CC13xx/CC26xx: Flash Programmer 2 fails to connect to CC13xx/CC26xx devices if the SCLK configuration in CCFG (Customer Configuration Area) is set to external LF clock.The reset options "hard" and "debug" are removed (SRFPROG-247). CLI: Cleaned up the list of available reset options.The issue is resolved by locking the GUI during the flashing procedure. GUI: Fixed issue where the flashing procedure is interrupted by clicking anywhere in the GUI (SRFPROG-296).GUI: Changed to a monospace font to increase the readability on high resolution displays (SRFPROG-298).GUI: Fixed several scaling issues seen on Windows 10 using high resolution displays (SRFPROG-291).The error message is improved and performing a mass erase is possible (SRFPROG-144). GUI: Fixed issues when performing actions directly after locking the debug interface.Fixed issue where package type naked die was not detected (LPRFTOOLS-307).Device revision now shows 2.5 (instead of 1.0) to align with the silicon revision specified in device errata note (SRFPROG-294).File content is now consistently overwritten (SRFPROG-234). Fixed issue where writing flash to file would sometimes append the data in an existing file.Fixed issue where reading a corrupt HEX file did not give an error message (SRFPROG-256).Fixed issue where secondary IEEE 802.15.4 and secondary BLE addresses were incorrect for CC13x2 and CC26x2 devices (SRFPROG-288).Fixed issue where SmartRF Flash Programmer 2 crashed when file size exceeded device size (SRFPROG-279).Validation of section header failed (SRFPROG-271). Fixed issue with programming of ELF file.Added a shortcut to Flash Programmer 2 in the top level folder of the installation directory (SRFPROG-310).To use hexadecimal input, add "0x" in the length field (SRFPROG-275). GUI Edit tab: The length field now supports both decimal and hexadecimal input.GUI Info tab: Extended the number of highlighted fields and added help text (SRFPROG-326).The device revision letter and number is now displayed in both the GUI and CLI (SRFPROG-327).Supported interfaces: 2-pin cJTAG, 4-pin JTAG and serial interface (UART).Added flash programming support for CC13x2 and CC26x2 devices (LPRFTOOLS-313).Release date: JanuNew Features and Enhancements Fixed incorrect package name for 7x7 QFN packages (SRFPROG-395).Removed redundant "." from pop-up window notifying that the debug interface is locked (SRFPROG-379).The GUI and CLI can be opened from any directory and remain fully functional (SRFPROG-319).If the length is larger than the device flash size, a popup window will appear and gives the option to proceed with the selected length or change it (SRFPROG-366). GUI Edit tab: Added validation for the length field. Updated emupack to version 8.5 (LPRFTOOLS-771).The JTAG pin setting is shown in the status window in GUI and log for CLI (SRFPROG-390).Added support for Intel-hex records "Extended Segment Address" (SRFPROG-388).The workaround is to connect to the device before reading memory (SRFPROG-194). CC2538 Edit tab: Reading "CCA" or "All flash" on CC2538 variants with less than 512KB flash will fail on the first attempt.See Troubleshooting section of the Flash Programmer 2 Help document. XDS200 Debugger: Flash Programmer 2 reports "Enumeration failed" if XDS200 firmware is outdated.The workaround is to adjust the settings or undock the image overrides (SRFPROG-360). GUI: When the resolution is set to low and the scaling is set high on a display, the application can get larger than the size of the screen or the windows can get compressed.It is always enabled on startup (SRFPROG-233). GUI: The "Auto-detect" checkbox state is not remembered between sessions.Using verification action when programming over the serial interface will fail if the file contains bits that lock bootloader access during programming (SRFPROG-377).If there are multiple boards connected and only 1 of them needs an update of XDS110 FW, the FW update is also triggered the other boards (SRFPROG-414).Possible when the FW image has been divided over 2 or more files. Fixed issue with programming of file with missing CCFG information in last flash page.Added flash programming support for CC2640R2L (LPRFTOOLS-410).Updated emupack to version 9.2 (LPRFTOOLS-864).Release date: JNew Features and Enhancements SmartRF Flash Programmer 2 will not target automotive customers since it is not qualified for automotive devices.Ĭustomers may use SmartRF Flash Programmer 2 for automotive devices, but it is the customer's responsibility to ultimately comply with regulatory requirements. This page list all relevant changes for the SmartRF Flash Programmer 2.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |